New Garage Doors for Roslindale MA Homes

New doors supplied and installed, and tired old doors replaced, for the detached single-car garages from the 1920s and 1930s that sit at the end of long driveways around Roslindale Village.
  • Open 24/7
  • Homes & businesses
  • 5.0 on Google

Schedule garage door service

Tell us what’s going on with your door and we’ll get back to you.

Loading the form.

What customers say about Elite Boston

Real reviews from Google.

Loading reviews.

A newly installed single-car sectional door with a row of windows across its top section on an old wood-framed detached garage

Why many Roslindale garages are due a new door

Around Roslindale Village, the typical garage is a modest outbuilding tucked behind a single- or two-family house, where a long driveway finally gives out, put up between the wars around an opening wide enough for one car. Plenty of them are on their second or third overhead door, and a few still carry one that has been patched, re-sprung and re-hinged until little of the original survives. New garage doors Roslindale MA homeowners enquire about tend to replace exactly that sort of veteran: sections rotted or rusted, balance long gone, more mending than door.

A new door on an old garage is not a box lifted off a warehouse shelf. The opening has had the best part of a century to settle, the header may sit low, and the framing may carry the scars of every door that hung there before. The door has to be picked and fitted for the building it is going into.

Three signs that a replacement is worth talking about:

  • Lower sections rusted through or spongy under a thumb, with rot creeping up the edges.
  • A door that has had springs, cables and hinges renewed and still runs roughly or drifts when stopped.
  • Splits in several sections, or a door that lets a ring of daylight in around most of its edge.

How a new door comes together

Measuring the opening as it is

Width high, low and in between; height on each jamb; clearance up to the rafters; and how far back the ceiling tracks can reach. Old openings seldom give the same reading twice.

Picking the door

Steel, insulated or plain, glazed or solid, in a style that sits comfortably on the house and the garage. Aluminium and glass full view doors are supplied and fitted too.

Removing the old one

Old springs are let down in the proper sequence, the door is dismantled a section at a time, and the old rails and brackets are taken away.

Fitting and balancing

Rails anchored into sound framing, sections stacked and hinged, springs matched to what the new door actually weighs, and the finished door balanced by hand.

Opener and controls

A healthy opener is reattached and adjusted; a worn one is replaced with a new unit, photo eyes, button and handsets.

Old openings and why measuring matters

A garage from the twenties or thirties has weathered a great many New England winters. The slab may have dropped at one corner, the header may dip a little at its centre, and the jambs may lean in or out. On top of that, earlier doors leave their marks: packers behind the jambs, extra timber nailed to the header, a scatter of holes where old rail brackets used to sit.

All of that bears on how a new door fits. A sectional door leaves the factory square. If the opening is not, the gap along the sides and top varies, the rubber along the bottom touches down unevenly, and the door may rub as it travels. So the tape goes across the opening near the floor, at waist height and under the header, and up each jamb, rather than one hurried reading. Where the error is bigger than weatherstripping can hide, the jambs or header are corrected as part of the job, or the rails are set to follow the opening so the door shuts snugly all round.

The slab gets the same scrutiny. A floor that falls away at one side can leave a wedge of daylight under a perfectly level door. A deeper bottom seal, or one cut to suit the slope, closes that wedge and keeps rain and leaves outside.

Low headroom and the door that fits under it

Single-car garages from this period often have only a narrow band of space over the header before the rafters begin. A standard sectional door wants that band for the curve where its rails turn from upright to overhead and for a torsion spring on its tube. Where the band is thin, a door can still go in, but the rail and spring layout changes. Many new garage doors Roslindale MA garages receive are fitted this way.

A low-headroom rail kit tucks the curve up near the ceiling and alters how the top section rolls over. Extension springs beside the overhead rails, or a torsion tube moved to the back end of the rails, can stand in for a spring over the door. Which suits a given garage depends on the readings, and it is settled before the door is ordered so the installation holds no surprises.

Depth counts too. The overhead rails reach back into the garage about as far as the door is tall, with the opener beyond that. In a short garage, that span may already belong to a workbench, a run of shelves or the nose of the car. Where rails and storage would clash, better to find out at the measuring visit than on the day.

Choosing a door for an old detached garage

The range is wide, and the best pick depends on the garage, the house and what the garage is used for.

Steel sectional doors are a popular choice for good reasons. They are fairly light, they will not rot, and they come in many panel patterns and colours. An insulated steel door sandwiches a core of insulation inside each section, which stiffens it, quietens it and keeps out cold and street noise. In a detached garage used only for parking, insulation might seem a luxury, but the extra stiffness also shrugs off dents from bins and bumpers and keeps the door true in a snug opening.

Glazing along the top section brightens an outbuilding whose only other light may be a single dusty pane, or none, which helps in a building lit by one bulb. A carriage-house pattern with decorative handles and hinges can suit an older house. For a crisper look, aluminium and glass full view doors are supplied and installed as well; our full view glass garage doors page shows the styles and how they are fitted.

Timber doors look right on some older garages, but they are heavier, need regular painting, and soak up moisture in a building open to every season. Owners replacing a rotted timber door often switch to steel. Whatever the material, the springs are sized for the real weight of the new door, so it balances correctly from its first run.

A new steel sectional garage door with a row of windows in the top section, fitted to a narrow old detached garage

Getting a new door down a long driveway

With the garage set so far back, everything travels the last stretch on foot. The door arrives as a stack of sections, along with rails, springs, brackets and boxes of fixings, and all of it is carried up the drive from the kerb. The old door leaves by the same route.

A clear path makes that easier. If cars can be parked elsewhere on the day, and the ground just inside and outside the doorway is cleared, the work runs faster with less risk of nicking a car or a fence. If the garage needs emptying to make room for the rails, doing that the evening before saves time.

What happens on installation day

Removal of the old door starts the day. Its springs are unwound in the right order, never cut under load, and the door is lowered and dismantled a section at a time. Old rails, brackets and the spring assembly follow, and any fixings in poor timber are noted for attention.

Then the opening is readied. Where the jambs or header need packing, shimming or fresh timber to give the new door a solid fixing, that work happens now. The lowest section of the new door is set level on the slab, the rest are stacked and hinged one above the other, and the upright and overhead rails are fixed to the framing.

Springs and cables come next. With a torsion setup, the coil goes onto its tube, the cables are wrapped onto the drums, and the coil is wound to match the door’s weight. With an extension setup, the springs, their containment cables and the pulleys are hung along the rails. The door is then balanced by hand: raised to several heights and checked that it stays where it is left.

Last, the opener, if there is one, is coupled up and adjusted, the photo eyes are mounted and aimed, the travel is set so the bottom edge meets the slab evenly, and a block of wood on the threshold confirms the door turns back when it meets resistance. Before the technician leaves, you are walked through using the release cord and the small signs worth watching for.

Garage door stuck or refusing to open?

Book a repair visit, ask about a new garage door, or call us now. We answer 24 hours a day.

Matching the door to the house

Houses around here each have their own character, and a garage door shows from the pavement even at the far end of a drive. A plain flush steel door suits some, a raised-panel or carriage-house pattern suits others. Colour matters as well: a door picked to echo the house trim or the garage siding looks intended, while a stark white door on a weathered garage can stand out more than anyone meant.

There is no single right answer. Bring photos of the house and the garage, or ask for an opinion at the measuring visit, and a door can be chosen to suit the building and the look you have in mind.

Planning the switch from the old door

Most replacements are planned rather than rushed. The door is measured, the style and options are agreed, and the new door is ordered for that opening. In the meantime the old door usually keeps going, sometimes after a small repair to keep it safe until the replacement arrives.

If the old door has failed completely, with a broken spring and rotten sections, it may need making safe first. It can be fixed shut, or its springs can be let down so it cannot fall, and the garage is used without a working door until the new one is in. If that failure happens after dark, our Roslindale emergency repair page covers keeping everyone safe in the meantime.

Springs sized for how the garage is used

A new door brings new springs, chosen for the door’s weight and for how often it will move. Behind a two-family house, one shared garage door can see a steady procession of trips from dawn to late evening. Springs rated for more cycles run exactly the same and can make sense in that case.

Spring choice also follows the space. Where nothing will fit above the opening, extension springs with containment cables, or a torsion tube set at the back of the rails, take over. Whichever goes in, the door is balanced by hand before the opener is reattached, because a balanced door is what keeps an opener healthy. For spring work later in the door’s life, see Roslindale spring repair.

Sealing a garage that stands alone

A standalone garage meets the weather on all four walls. Wind drives rain under a tired bottom seal, snow banks against the door all winter, and the air inside swings from summer swelter to winter chill. A new door is the moment to seal the opening properly.

The bottom seal is matched to the floor, dips and slopes included. Weatherstripping along the jambs and header closes the gap round the sides and top. An insulated door helps further by stopping the sections flexing and opening up in a gale. In a garage used as a workshop or for storage, the drop in draughts and damp is easy to feel.

Handles, locks and the small fittings

A door is more than its sections and springs. Each new door arrives with its own hinges, rollers, end caps, a top fixture for the opener arm, and, where wanted, an outside handle and a lock. On an old garage that has gone through several doors, these small fittings are where earlier installers often cut corners: rollers reused from the previous door, a lock bar left in place but no longer lining up with any slot, hinges mixed from different sets. With a fresh door, everything matches and is set up together. New garage doors Roslindale MA owners put on manual operation, with no opener, can have a slide lock fitted on the inside and a handle on each face of the bottom section, so the door is easy to lift from the drive and secure from within. Where an opener is fitted, an inside lock is usually left off or disabled, because an opener driving against a locked door can bend the top section.

Keeping or replacing the opener

An existing opener can often serve a new door, provided it is in good order and has working photo eyes and auto-reverse. It is coupled to the new door, its travel and sensitivity are adjusted for the new weight, and it is tested.

If the opener is old, loud or lacks modern safety features, swapping it alongside the door spares a second visit later. We repair and replace LiftMaster openers among others, and a replacement unit goes in complete with its rail, eyes, button and handsets, all set up and tried. See Roslindale opener repair for opener work in more depth.

Repair or replace the existing door

Not every weary door needs replacing. If the sections are sound and the trouble lies in springs, cables, rollers or hinges, mending it is usually the better choice; read Roslindale garage door repair for that side of things.

Replacement becomes the right call once the sections themselves give out: steel rusted through, timber rotten or split in several places, or a door so waterlogged it can no longer be balanced. The same holds when a door has had fix after fix and still runs badly, or no longer suits how the garage is used. An honest view of which way to go is part of every visit, and new garage doors Roslindale MA homeowners are shown are never pressed on anyone where a repair will serve.

Starting with a new door

It begins with a measuring visit: the opening, the framing, the headroom and the options, talked through on site. Calls are taken day or night, so get in touch whenever suits you. Our citywide installation work is described under new garage door installation, and the Roslindale page gathers every service we offer locally.

When asking about new garage doors Roslindale MA garages need, mention roughly when the garage was built, what the present door is made of, whether an opener is fitted, and whether the rafters sit close above the opening. With that sorted, call us or book online and a measuring visit can be arranged.

Questions from Roslindale

Our opening is a little out of square. Will a new door still seal?

Yes. Readings are taken at several points, and where the opening is off, the jambs or header are corrected or the rails are set to follow it, with a bottom seal picked to suit the floor.

The rafters sit right above our opening. Can a sectional door still go in?

Usually. A low-headroom rail kit and a different spring layout let a sectional door fit where there is very little clearance overhead.

What becomes of the old door?

It is taken down safely, springs let down in the right order, and removed along with its old rails and fittings.

Does a new door mean a new opener too?

Not necessarily. A healthy opener with working photo eyes can be reattached and adjusted for the new door. An old or unsafe one is better replaced at the same visit.

How do the sections reach a garage so far from the street?

By hand, up the driveway, along with the rails and fittings. Clearing cars off the drive for the day makes it quicker and easier.

Garage door stuck or refusing to open?

Book a repair visit, ask about a new garage door, or call us now. We answer 24 hours a day.

Schedule garage door service

Tell us what’s going on with your door and we’ll get back to you.

Schedule garage door service

Loading the form.

Elite Boston Garage Door Repair & Supply
590 Shawmut Ave, Boston, MA 02118
Hours: Open every day, 24 hours.