New Garage Doors for Roxbury, MA Homes

New garage doors supplied and installed, and tired old doors replaced, on the rear garages behind Roxbury’s three-deckers and Victorians, including openings on steep lots and shared drives. Questions are answered at any hour, every day of the week.
  • Open 24/7
  • Homes & businesses
  • 5.0 on Google

Schedule garage door service

Tell us what’s going on with your door and we’ll get back to you.

Loading the form.

What customers say about Elite Boston

Real reviews from Google.

Loading reviews.

A rear garage behind a three-decker with a new sectional door, at the top of a steep shared driveway

Fitting a new door to an old Roxbury garage

The garages around Nubian Square and Fort Hill are mostly single rear garages behind three-deckers and Victorians, and many of the row houses nearby have none at all. A lot of those garages have outlived several doors already. The frame around the opening has settled, the slab has followed the slope of the lot, and the door hanging there now may be a patchwork of replaced sections and mismatched hardware. Choosing new garage doors Roxbury MA homeowners can rely on starts with that reality: whatever goes in must fit the crooked, settled Roxbury opening that actually exists.

Fitting a door well on these lots also means planning around how the garage is reached. A new door turns up as a stack of long flat panels, rails, a spring on its shaft and cartons of brackets and bolts, every bit of which travels on foot along a steep driveway that is often shared with the house next door.

Three things are useful to know before we talk about a new door:

  • Roughly how wide and how tall the opening is, and whether it looks square.
  • Whether the floor at the opening is level, or falls away toward one side or toward the drive.
  • Whether the garage has an opener you want to keep, or would like a new one fitted with the door.

What a new door for a Roxbury garage can be

Insulated steel sectional doors

The most common replacement for a rear garage. Sections roll up under the ceiling, take little space in front of the opening, and suit a narrow shared drive.

Doors in a style that suits the house

Raised or flush panels, windows along the top section and a colour picked to sit well with a three-decker’s siding or a Victorian’s trim.

Full view aluminium and glass

Where the garage doubles as a workshop or studio, a full view door floods it with daylight. The full view glass garage doors service has the details.

Low-headroom arrangements

Older rear garages often have little space above the opening. A low-headroom track and spring layout lets a sectional door fit where a standard one will not.

Bottom seals for sloping floors

Where the slab tilts, the new door gets a bottom seal picked to meet the slab from one jamb to the other, so water running down the drive stays out.

A matching opener

A new door can be fitted with a new opener set up for it from the start; see Roxbury opener repair for the opener side.

When a new door makes more sense than another repair

Plenty of failures on these garages are fixable, since springs, cables, rollers and openers are built to be swapped, and our Roxbury garage door repair page deals with all of them. Replacement wins only once the panels themselves, not the hardware hung on them, are finished.

On Roxbury’s sloping lots, that end usually arrives from the bottom up. Run-off from the drive soaks the lowest section year after year, steel rusts through along the bottom edge, and timber goes soft and starts to crumble. On a shared drive, the bottom corners and the lower sections take repeated knocks from bumpers turning in a tight space, until the door no longer runs true in its rails. And a timber door in a damp garage gradually absorbs so much water that it becomes too heavy for any spring to balance properly.

Other signs are quieter: a door that has had so many sections replaced that none of them match, hinges cracking faster than they can be replaced, or an old one-piece door that swings out over the drive and has to be dodged by anyone walking past. Any of those makes it worth weighing a new door against another round of repairs.

Measuring an opening that has moved

Measuring for a new door in a newer garage is straightforward. In a rear garage behind an older three-decker or Victorian, it takes more care. Timber openings settle, jambs drift off plumb, and a header can dip toward its centre. Measuring the width once at the floor and the height once at one side can produce a door that binds at the top or leaves a gap at one jamb.

So we take a tape to it more than once: width across the slab, across the middle and just under the header; height up the left jamb, the right jamb and the centre; and the diagonals, which show whether the opening is square. The headroom above the opening is measured to the lowest obstruction, whether a joist, a beam or a pipe, and the side room either side of the opening is checked for the vertical rails and the spring.

If the frame has racked badly, jambs and header get packed out or trued up first, so the new door hangs in a straight frame instead of copying the old door’s twist. You will be told if that is the case before any order is placed.

New garage doors Roxbury MA: setting a door on a sloping slab

Steep grades are the normal working conditions here, and they shape the slab the door closes onto. On many rear garages around Fort Hill the floor falls with the lot, lower at one jamb than the other, or the driveway runs downhill into the opening and meets the slab at a lip. Fitting new garage doors Roxbury MA lots like these have means deciding how the door will meet that floor.

The door itself must hang level and square in the opening, with the rails plumb, or it will rack and wear unevenly. The floor, though, is not level, so the gap between the bottom of the door and the slab varies along its length. That gap is closed with the bottom seal, chosen and sometimes trimmed to suit the actual slope, and on a badly sloping slab a threshold or a reshaped bottom section can be used. The opener’s down limit is then set so the door stops when the seal meets the floor all the way along, rather than pressing down on the high side.

On a drive that tips toward the garage, that seal doubles as the door’s flood barrier. A new door with a well-fitted seal keeps run-off and leaves out of the garage and stops the bottom section of the new door from going the same way as the old one.

Installers lifting a new garage door section up a steep shared driveway toward a rear garage

Getting the new door up the drive

A new single-car door arrives as several long, flat sections, two vertical and two horizontal rails, the spring assembly and its shaft, and the hardware to hang it all. Up a steep Roxbury shared driveway, every one of those pieces is walked from wherever the van could park. That shapes the day: the drive needs to be clear of cars for its whole length, there needs to be somewhere flat near the garage to lay the sections down, and the neighbours who share the drive need to know it will be busy.

The old door has to come down and out the same way. On the old door the torsion spring is unwound with proper bars before a single bolt is loosened: that coil holds dangerous tension, and cutting it loose, or freeing it as a DIY repair, is how people get hurt. The old sections are taken down one at a time from the top, and the old rails are removed.

What installation involves

Fitting the new door is done in a set order, so it ends up balanced and square:

  1. The empty opening gets a final check, any soft or crooked framing is put right, and fresh weather stripping goes round the sides and top.
  2. The lowest panel goes in first, levelled across the opening, with its seal fitted for the slab, and the remaining sections are stacked on top and hinged together.
  3. Upright rails go on dead plumb at both sides, the overhead rails are hung back to the joists, and every roller is seated.
  4. The spring assembly is mounted, the cables are run to the bottom brackets, and the spring is wound to balance the door’s actual weight.
  5. The door is tested by hand: it should lift easily and stay where it is left at mid height.
  6. Whichever opener the door will use, new or kept, is hooked up and taught this door’s travel and force on this slab, then its eyes and auto-reverse are proved.

Before we leave, we show whoever uses the garage the red release cord, how to run the door by hand in a power cut, and which early noises are worth a phone call.

Garage door stuck or refusing to open?

Book a repair visit, ask about a new garage door, or call us now. We answer 24 hours a day.

What to ask about before choosing

A new door is a long-term part of the building, so it is worth thinking about how the garage is really used. Is it for one car, or for storage shared between units? Is it opened many times a day, or once or twice a week? Does anyone use it as a workshop? Does water already come in under the old door when it rains? Each answer points toward a particular kind of door: a stiffer insulated door for a garage that takes knocks on a tight drive, a well-specified seal for one at the bottom of a slope, windows for a garage used as a workspace, and a quiet, smooth-running opener for a door that moves all day.

Choosing new garage doors Roxbury MA rear garages will carry for a long time is easier with those answers to hand. It also helps to know who in the building has a say, if the garage is shared, so the choice is settled before the order is placed.

Retiring the old door

Plenty of the doors being replaced on these lots are old one-piece tilt doors or wooden sectionals that have been patched again and again. Taking one down is a job in itself. A one-piece door is held up by heavy side springs on pivoting arms, and those springs stay loaded until the door is fully released; a wooden sectional may have rotten sections that break apart as they are lifted. Each is taken down in a controlled order, with the springs made safe first, and the opening is cleared down to bare framing so it can be checked before the new door goes up.

This is often the point at which hidden problems show: a rotten jamb behind old trim, a header that was carrying the old door’s weight badly, or a slab that has cracked where the old door landed. Those are put right before the new door is hung, so it starts its life in a sound opening.

Choosing a door that suits the house

The houses around Nubian Square and Fort Hill are three-deckers and Victorians, and a rear garage usually sits within sight of the back of the house. A new door does not need to match anything exactly, but it is worth choosing one that sits comfortably with the building: raised panels for a door seen alongside a Victorian’s trim, a flush or plain panel against simple siding, and a colour that ties in with the house’s windows or doors.

Glazing along the uppermost panel lets daylight into a garage that does more than house a car, and they sit high enough to keep the contents out of view. A full view aluminium and glass door goes further, turning the garage front into one large window, which some owners use for a workshop or a studio at the back of the lot.

Insulation and a damp rear garage

A rear garage is usually unheated, but insulation in the door still matters. An insulated steel door is stiffer than a single-skin door, so it resists the dents a bumper or a bin leaves on a narrow drive. It is also quieter as it moves and less prone to condensation on the inside face, which helps in a garage that already takes water from a sloping drive. Anyone using the space as a winter workshop will feel the difference.

Living with the new door

A new door on a sloping rear garage settles in over its first weeks. Springs relax slightly, the seal beds into the slab, and the rails find their final position against the framing. If the door starts to drift when left halfway, closes with a bump, or leaves daylight under one corner, mention it: those are small adjustments, and catching them early keeps the door balanced. Keeping the bottom of the door clear of packed snow and leaves through the winter, and rinsing grit off the seal now and then, helps it last on a drive that sends everything toward the garage.

Doors for garages with little headroom

Older rear garages often have only a short strip of wall above the opening before the ceiling joists start. An ordinary sectional layout wants room overhead for the rails to bend back and for a spring shaft across the header. Where that space is missing, a low-headroom arrangement changes how the rails curve and where the spring sits, so a sectional door can still be fitted. The headroom is measured at the survey, and the door is specified for the garage as it is.

Shared garages and a new door

A rear garage behind a three-decker is often shared between the units, and a new door changes things for everyone who uses it. It is worth agreeing the colour and style between the households, deciding how many remotes are needed if a new opener is fitted, and making sure everyone knows how to release the new door by hand. On the day, every car using the shared drive needs to be moved, so agreeing a date that suits the building helps the work run smoothly.

Talking about new garage doors

For anyone weighing up new garage doors Roxbury MA rear garages can take, the starting point is a conversation about the opening, the slab and how the garage is used. Someone answers our line whatever the hour, so a question about a new door can be asked whenever it occurs to you. Our wider new garage door installation service explains more, and every local service is together on the Roxbury page. If the current door has failed suddenly and you need it made safe first, the Roxbury emergency repair page covers that, and a broken spring on the old door is covered on Roxbury spring repair.

When you are ready, tell us the size of the opening if you know it, whether the floor slopes, whether you want an opener with the door, and how the garage is reached. Whether the garage is up on Fort Hill or down nearer Nubian Square, call us or book online to arrange a survey.

Questions from Roxbury

Our garage floor slopes. Can a new door still close properly?

Yes. We hang the door true, then pick and trim a bottom seal that fills the tapering gap on your tilted slab. The opener’s down limit is then set for that floor.

The opening is not square. Will a new door fit?

Usually. We measure it repeatedly at different points, and a badly racked frame is straightened before the door goes in.

Can the new door be brought up our steep shared driveway?

Yes. The sections and rails are carried up by hand. It helps if the whole shared drive is clear of cars and the neighbours know the date.

Should we replace the opener at the same time?

It is often sensible, especially if the old opener is struggling or does not suit the new door. A healthy existing unit can stay, re-taught for its new door.

Is there room for a sectional door in a low rear garage?

Usually. Where there is little space above the opening, a low-headroom rail and spring arrangement lets a sectional door fit. The headroom is measured at the survey.

Garage door stuck or refusing to open?

Book a repair visit, ask about a new garage door, or call us now. We answer 24 hours a day.

Schedule garage door service

Tell us what’s going on with your door and we’ll get back to you.

Schedule garage door service

Loading the form.

Elite Boston Garage Door Repair & Supply
590 Shawmut Ave, Boston, MA 02118
Hours: Open every day, 24 hours.